1923 Limbus Avenue
Sarasota, FL  34243
24 Hour Service
Home      About Us      Services         Scope        Gallery      Contact

Gallery     All photos displayed on our web site show equipment repaired by Regional Engineering & Service.

Peerless vertical turbine pump model 20XB

Layne vertical mix flow pump

Bingham boiler feed water pump MSD 3x6x9C

(2) KSB submersible pumps: ANACAM PA 43hp (left) and KRKT 137hp (right)

Lawrence propeller pump model 16BPO

Goulds horizontal split case pump model 3463

Ingersoll-Rand boiler feed water pump model 3CNTA-8 nearing completion

One coming in, one going out: I-R boiler feed water pumps model DA-9 (front) DA-8 (rear)

(2) Union high pressure vertical turbine pumps type F485x840

A day in the life.

Goulds high pressure vertical turbine pump model 11RALC

Terry GF-7 steam turbine lower case prior to rotor installation.  Note RE&S manufactured HP step seal.

Elliot steam turbine type 2EPGH

Terry GF-7 steam turbine diaphragms with RE&S manufactured interstage labyrinth seals installed and ready for line bore.

Elliott steam turbine model BYRT

Calder energy recovery hydraulic turbine model A3101

Dodge gear reducer model TXM 1200

Hoffman blower model 74207

Amarillo gear reducer model A32

Marley gear reducer model 9-4136-A

Westfalia centrifuge bowl assembly model DA-100-16-117

American Standard Gyrol Fluid Drive model 315

Summit 30x6x120 lathe with tire shredder shaft

Acer mill completing Allis-Chalmers carbon seal housing

IEM balancing stand with Phelps Dryer Fan rotor (note ceramic coat on impeller)

Machining packing box face for mechanical seal on I-R 3CNTA-8 BFW pump

Summit 19-4 lathe with tool post grinder finishing bearing journal on tire shredder shaft.

Eutectic spray metal overlay on horizontal pump split line erosion.  Repair area will be milled, filed, and stoned to restore plane.

NDT inspection; verifying cracked bushing casting in vertical turbine pump section bell.

Plate and structural material in stock in our shop.

Various materials round bar drops in stock in our shop.

Various materials full length rounds and structural material in stock in our shop.

Centrifugally cast bronze tubing in stock in our shop.

Large diameter 932 centrifugally cast bronze tubing in stock in our shop.

Large diameter alloy tubing and bar in stock in our shop: 304, 316, 17-4, 4140, 4340, 1026, 410, 416, Nitronic 60, Ferallium 255, Hastelly C276, Duplex, and Super Duplex.

IEM balancing stand with I-R 3CNTA- BFW pump rotor.  Note coupling hub installed.

Field repair of Terry GF-26 steam turbine inlet valve.

Patterson horizontal split case pump model 18x200 MABS-D repaired in our shop, installed and aligned.

Worthington boiler feed water pump model 4UNQ-11 repaired in our shop, installed, and prepped for laser alignment.

Floway vertical pump model 24MF repaired in our shop and shown during installation. Pump will be leveled, motor installed, and rotor lifted to operating height prior to observing start up.

Allis-Chalmers single stage blower model D-48 JR during field installation of new carbon seal housing, (2) seal rings, and cover.

Union high pressure horizontal split case pump model DVSS 10.12.14 HH inspecting thrust end radial babbitt bearing.

Layne vertical mix flow pump installed.

Flowserve vertical turbine deep set aquafier pump model 2ENL installed.

Allis-Chalmers single stage blower model D-48 JR during field inspection of radial and thrust bearings.

Lawrence propeller pump model 16BPO.  RE&S stainless steel impeller with OEM prop cap on left, OEM impeller removed from service on right.

Two 932 bronze shaft bushings for a vertical turbine pump manufactured by RE&S (top) with sample bushing removed from service (bottom)

Inside bearing housing cover for I-R 3CNTA-8 boiler feed water pump.  New RE&S cover (left), OEM cover removed from service (right).

Two tire shredder shafts manufactured by RE&S.

Replace suction bell shaft bushing casting as part of a vertical turbine pump repair.

Aurora vertical sewage pump model613A 12x14x22A back plate with integral packing box and packing gland manufactured by RE&S.

Barnes model 4SE1134L maserator type open face sewage impeller manufactured and dynamically balanced by RE&S.  Note ceramic coat.

I-R 3CNTA-8 boiler feed pump parts manufactured by RE&S including pump shaft, shaft sleeves, shaft sleeve nuts, drive end bearing carrier, and impeller suction and hub wear rings.

Union high pressure horizontal split case pump model DVSS 10.12.22A spherical radial babbitt bearing during RE&S repair.

Custom mechanical seal parts for vertical turbine pump manufactured by RE&S to suit OEM housing (top right).

8.647" turbine generator split radial bearing.

9.432" turbine generator split radial bearing.

Stainless steel external fresh water flush line for vertical turbine pump designed and installed by RE&S.

Too much chlorine in the neighborhood.  Corrosion of a bronze vertical turbine pump shaft bearing.

Tow away zone.

Low PH problems present in a vertical turbine pump suction bell.

Life springs eternal.  Sprout growing between packing and lantern ring in the packing box of a Goulds horizontal split case pump.

"The job is very straightforward..."

Incoming.

"Bond, James Bond"
HomeAbout UsServicesScopeGalleryContact Us

Copyright 2011 Regional Engineering & Service: Blower Repairs. All Rights Reserved.
(941) 755-1583
1923 Limbus Avenue, Sarasota, FL  34243
Founded 1979
941-755-1583